Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
What're your thoughts concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily accessible, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and also position the new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have certified yourself for the work and are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will assist you install a new bath tub in your restroom if you have actually already gotten a new tub as well as don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Protect the tap in place with the manufacturer offered backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Utilizing the two wood boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break a stiff seal, triggering the water to permeate the wall surface between the bath and also the tiling, leading to complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can crack fairly early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about Tools You Need to Install a New Bathtub and I'm hoping you liked the blog post. If you appreciated our blog post please remember to share it. Kudos for your time. Kindly come by our website back soon.
Information
Report this page